DOSCO Hydraulic Gear Pumps
GPM Bushing Gear Pump Range
- Flow Dividers
- Step-Down Pumps
- Spare Parts
Speeds up to: 3000 RPM
Pressure up to 240 BAR
Displacements between 10cc/rev to 147 cc/rev
Brochure / Datasheet
Click on BLUE HEADLINES to open and shut each page
PUMPS & MOTORS
Fluid Power for Mobile Equipment
GPM hydraulic pumps and motors are particularly well suited to mobile equipment applications; they are designed for extreme duty cycles, and continuous heavy duty operation. Whilst the equipment is of a simple yet rugged design, it is manufactured to extremely precise tolerances.
Pumps are available in capacities ranging from 11 cc/rev to 200 cc/rev for each gear section. Several sections can be combined into one assembly. A wide selection of SAE and ANSI mounting flanges and drive shafts are available for all drive units. Pipe thread, 0-ring seal, and split flange ports are available in both metric and SAE standards.
GPM pumps are manufactured under statistical analysis process control which is monitored by the South African Bureau of Standards to an ISO 9001-2008 quality management system.
Sectional Construction: Standard Parts can be assembled in a wide variety of configurations to suit almost any application. All gear housings are cast from an extra complex iron with a minimum tnsile strength of 380 Mpa (55000 Psi) and hardness between 200 and 250 Brinell.
Multiple pump units: Several pump sections can be combined in a single drive, to eliminate multiple drive P.T.O units. Precision matched gears: All gears are manufactured from high alloy forged bars, surfaces are super finished and each gear pair is matched for maximum efficiency. The deep 1 0-tooth pattern gives maximum output per revolution whilst ensuring low pulsation frequency.
Bearings: Latest technology Teflon plain bush bearing are utilized on all gear journals to improve pressure and speed capability.
Motors: are available with capacities ranging from 83 NM to 517 NM @ 1000RPM. Basically similar in design to pumps, they are engineered for extreme heavy duty applications, with high efficiency characteristics. Motor speed is in direct proportion to the volume of oil delivered to the inlet port and output torque is in proportion to the pressure supplied to the motor. All other equipment required to match our pumps and motors is readily available.
GPM hydraulic equipment is direcUy interchangeable with the other internationally recognized SAE pumps and motors. GPM equipment is sold in component form but units can be assembled and tested to meet your particular requirements.
Each section of a pump or motor should be regarded as a single unit with corresponding power input requirements. The entire input horsepower is fed through the drive shaft, the power delivered to or from the unit is limited by the strength of the shaft. The limit is defined as the “PL” factor. The “P” being the operating pressure In PSI and the “L” the sum of the gear widths in Inches.
In multiple units the “PL” must be calculated for each connecting shaft and must include the sum of the gear widths driven by it. (Each shaft has a unique “PL” factor as can be seen in the table below).
Pressure (PSI) x Total Gear Width (Inches) = PL Factor
PL FACTOR MUST NOT EXCEED FIGURE SHOWN IN CHART FOR SHAFT TYPE
Contact us about this Pump Range
Our Head Office and Production Facilities are at:
6 Impangela Road, Sebenza Ext. 6, Edenvale, 1609 Gauteng, South Africa.
Our Middelburg office is located at 11 Hektaar St, Middelburg, 1050 Mpumalanga, South Africa.
We are open from Monday to Thursday: 08:00-16:45, Fridays: 07:30-15:00.
Switchboard: +27 11 452 5843
SALES MANAGER: Wimpie Potgieter: +27 82 419 0708
KAWASAKI & GPM PRODUCT SPECIALIST: Rob Masterton: +27 66 307 3236
Managing Director: Jacques Lombard: +27 82 651 2152
DOSCO Middelburg: +27 13 246 1227
MIDDELBURG SALES: Leon Labuschagne - +27 72 216 7334